EXAIR Corporation

Blowoff Comparison

There are a variety of ways to blow the water from the bottles shown in the photo to the right, but which method is best? The following comparison of drilled pipe, flat air nozzles, a blower and the Super Air Knife proves that EXAIR has the best choice for your blowoff, cooling or drying application.

Our goal for each of the blowoff choices was to use the least amount of air possible to get the job done (lowest energy and noise level). Compressed air pressure required for each was 60 PSIG (4.1 BAR) which provided adequate velocity to blow the water off. The table below summarizes the overall performance. Since your actual part may have an odd configuration, holes or sharp edges, we took sound level measurements in free air (no impinging surface).

EXAIR Model 110012 Super Air Knife

(2) Model 110012 12" (305mm) Super Air Knives blow water off bottles prior to labeling.

Compare These Blowoffs

ineffective drilled pipe

Drilled Pipe

This common blowoff is very inexpensive and easy to make. For this test, we used (2) drilled pipes, each with (25) 1/16" (1.6mm) diameter holes on 1/2" (13mm) centers. As shown in the test results below, the drilled pipe performed poorly. The initial cost of the drilled pipe is overshadowed by its high energy use. The holes are easily blocked and the noise level is excessive - both of which violate OSHA requirements. Velocity across the entire length was very inconsistent with spikes of air and numerous dead spots.

Order a Super Air Knife today!
ineffective flat air nozzles

Flat Air Nozzles

As shown below, this inexpensive air nozzle was the worst performer. It is available in plastic, aluminum and stainless steel from several manufacturers. The flat air nozzle provides some entrainment, but suffers from many of the same problems as the drilled pipe. Operating cost and noise level are both high. Some manufacturers offer flat air nozzles where the holes can be blocked - an OSHA violation. Velocity was inconsistent with spikes of air.

ineffective blower

Blower Air Knife

The blower proved to be an expensive, noisy option. As noted below, the purchase price is high. Operating cost was considerably lower than the drilled pipe and flat air nozzle, but was comparable to EXAIR’s Super Air Knife. The large blower with its two 3" (76mm) diameter hoses requires significant mounting space compared to the others. Noise level was high at 90 dBA. There was no option for cycling it on and off to conserve energy like the other blowoffs. Costly bearing and filter maintenance along with downtime were also negative factors.

Exceptional EXAIR Super Air Knife

EXAIR Super Air Knife

The Super Air Knife did an exceptional job of removing the moisture on one pass due to the uniformity of the laminar airflow. The sound level was extremely low. For this application, energy use was slightly higher than the blower but can be less than the blower if cycling on and off is possible. Safe operation is not an issue since the Super Air Knife cannot be dead-ended. Maintenance costs are low since there are no moving parts to wear out.

Blowoff Comparison Statistics
Type of Blowoff PSIG BAR SCFM SLPM Horse Power Required Sound level dBA Purchase Price *Annual Electrical Cost Approx. Annual Maint. Cost First Year Cost
Drilled Pipe 60 4.1 174 4,924 35 91 $50 $4,508 $920 $5,478
Flat Air Nozzles 60 4.1 257 7,273 51 102 $208 $6,569 $1,450 $8,227
Blower Air Knife 3 0.2 N/A N/A 10 90 $5,500 $1,288 $1,500 $8,288
Super Air Knife 60 4.1 55 1,557 11 69 $594 $1,417 $300 $2,311
*Based on national average electricity cost of 8.3 cents per kWh. Annual cost reflects 40 hours per week, 52 weeks per year.
 
Copyright © 2017 EXAIR Corporation. All rights reserved.