Cooling
Customer manufactures sign displays. They use a router to cut out various shapes from a plastic sheet. The router bit heats up causing the plastic to melt, ruining the cutout. The edges have to be perfectly smooth because the signs are edge lighted. To avoid this they have to slow way down and take nibble cuts. Installing the Model 3925 Adjustable Spot Cooler onto the router head and directing the chilled air onto the router bit, heat was eliminated and they were able to get a clean sharp cut. The customer estimated that they saved $8 per sheet in labor and scrap.
-
Model 3903 Hot Muffler for 2-40 SCFMNoise Muffling: EXAIR offers mufflers for both the hot and cold air discharge. Normally, muffling is not required if the cold air is ducted. Learn More$39.00
-
Model 15-C Generator for Medium Vortex Tubes (15 SCFM)Generators set the total volume of air flow through the Vortex Tube and are available to create the coldest temperature possible or the best Btu/hr. values. Learn More$23.00
-
Model 8-R Generator for Small Vortex Tubes (8 SCFM)Generators set the total volume of air flow through the Vortex Tube and are available to create the coldest temperature possible or the best Btu/hr. values. Learn More$24.00
-
Model 4-TS Taper Sleeves Only for Vortex Tube Generators (4 SCFM)Taper Sleeves are used with small Vortex Tube Generators Learn More$12.00
-
Model 3557 Buna-N O-Ring (Medium Vortex Tube Generators)
Buna-N O-ring for Medium Vortex Generators
Learn More$2.00 -
Model 4-GC Generator for Small Vortex Tubes (4 SCFM)Generators set the total volume of air flow through the Vortex Tube and are available to create the coldest temperature possible or the best Btu/hr. values. Learn More$12.00
-
Model 3594 Generator Kit and Small Parts for Small Vortex TubesGenerator Kit for small Vortex Tube Cooling Kit Learn More$51.00
-
Model 3410 Vortex Tube (10 SCFM)EXAIR's Vortex Tubes offer a low cost, reliable, maintenance free solution to a variety of industrial spot cooling problems. Using an ordinary supply of compressed air as a power source, vortex tubes create two streams of air, one hot and one cold, with no moving parts. They are constructed of wear resistant stainless steel, which is ideal for corrosive and hygienic environments. Learn More$262.00
-
Model 3901 Cold Muffler for 10-40 SCFMNoise Muffling: EXAIR offers mufflers for both the hot and cold air discharge. Normally, muffling is not required if the cold air is ducted. Learn More$44.00
-
Model 3725 Adjustable Spot Cooler onlyEXAIR's compressed air powered Adjustable Spot Cooler offers a low cost, reliable, maintenance free solution to a variety of industrial spot cooling problems. With the turn of a knob, you can select a precise temperature setting from -30°F (-34°C) to room temperature. Learn More$402.00
-
Model 3215 Vortex Tube (15 SCFM)EXAIR's Vortex Tubes offer a low cost, reliable, maintenance free solution to a variety of industrial spot cooling problems. Using an ordinary supply of compressed air as a power source, vortex tubes create two streams of air, one hot and one cold, with no moving parts. They are constructed of wear resistant stainless steel, which is ideal for corrosive and hygienic environments. Learn More$262.00
-
Model 8-GR Generator for Small Vortex Tubes (8 SCFM)Generators set the total volume of air flow through the Vortex Tube and are available to create the coldest temperature possible or the best Btu/hr. values. Learn More$12.00
Filter
No Filter Found